Paint over Rust with Underbody Gloss Black Paint, Gallon, TRC-15, RUST-BITE

Description

This sale is for one gallon of Paint over Rust with Underbody Gloss Black Paint, TRC-15, RUST-BITE
TRC-15 Gloss Black
• Home • Auto Restoration • Industrial • Fleet • Marine •
TECHNICAL DATA
SUGGESTED USES:
Heavy equipment, trucks, snow plows, mower decks, tractors and other
farm machinery, oil field equipment, boat trailers, buses, military vehicles,
dumpsters, roll offs, fork lifts, propane tanks, truck bodies, storage tanks,
structural steel, pipes, iron works, gates, fence posts, chain link, steel truck
rims, metal roofs, sheds, and concrete floors.
DESCRIPTION:
Rust-Bite is a high solids, VOC compliant, single component rust preventive
and underbody coating specifically formulated to permanently stop
corrosion without the use of primers or topcoats. Rust-Bite protects many
surfaces from water, chemicals, salt, and other corrosive contaminants. Rust-
Bite stops rust when applied to rust that is prepared by using a wire brush or
hand scraper to remove all loose rust or scale. For optimum adhesion
sandblast with medium grit. Rust-Bite will dry to a flexible rock hard, nonporous
finish that will not crack, chip, flake or peel. Rust-Bite cures by
reacting with atmospheric moisture and its cured film resembles that of a
powder coating or a baked-on finish with the use of no hardeners or heat.
Rust-Bite seals and protects many surfaces from road salt, gasoline, diesel
fuel, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Rust-Bite can be top coated with any industrial or automotive finish.
PREPARATION
Remove all dirt, grease or oils, clean surfaces using a Wax & Grease
Remover or equivalent. For heavy build-up scrape or wire brush excess
material prior to degreasing. Allow surfaces to dry thoroughly. NOTE: Do
not apply Rust-Bite if atmospheric temperature is below 50°F.
RUSTED SURFACES:
Remove loose rust and scale using a stiff wire brush, by grinding, or hand
tool cleaning. Remove all loose, peeling or bubbling paint. NOTE: Rust-Bite
works best when applied directly over rust. NOTE: Do not remove all rust or
apply any type of Rust Converter before applying Rust-Bite.
BARE, SMOOTH METAL:
Sandblasting is recommended but sanding with 36 to 80 grit sand-paper is
also acceptable. When blasting, provide a medium to coarse profile for
optimum adhesion. Avoid any media that may leave a smooth surface.
PAINTED SURFACES:
Previously painted surfaces should be sanded using a 120 to 180 grit
sandpaper to remove gloss.
MIXING & HANDLING:
Container may be under slight pressure. Stir liquid gently until uniformly
mixed. Do not shake, shaking will cause Rust-Bite to build pressure in can.
Never work directly from the Rust-Bite can unless the entire contents will be
used in a single painting session. Always pour what will be used into a
separate container.
NOTE: Never pour unused product back into original
container after use.
NOTE: Before closing Rust-Bite container apply a sheet
of plastic or food wrap over can, Rust-Bite will adhere lid to can if plastic is
not applied.
Never allow can to sit opened when not in use. WEAR
GLOVES DURING USE Skin contact should be avoided. Do not attempt to
remove dried Chassis Saver from skin with solvent; soak in warm, soapy
water. Once product has stained skin, only time will remove it.
APPLICATION & REDUCING:
Apply 2-4 coats allowing 3 to 8 hours between coats depending on temp
and humidity. Each coat should be dry to touch with no tackiness before
applying next coat. Rust-Bite is a moisture cure finish which when applied
too heavy will have a tendency to bubble while curing. Avoid bubbling by
applying thin coats only. Higher temps and humidity will shorten drying
time. Low temp and humidity will lengthen dry. Do not apply Rust-Bite if
temperature is below 50°F. Never use lacquer thinner as a reducer for Rust-
Bite or to wipe surfaces prior to painting.
BRUSH APPLICATION:
Apply thin, even coats using a nylon brush. For better flow and leveling, add
up to 10% TRC-01 Reducer.
SPRAY APPLICATION:
Reduce up to 10% using TRC-01 Reducer. Apply medium-wet coats while
maintaining a gun distance of 12 to 14 inches. Spray tip size should be: 1.2 to
1.4mm.
NOTE:
For surfaces that will be
exposed to UV (sunlight), wait 24 hours, sand and apply a UV resistant single stage urethane paint.
RECOAT:
For films cured over 24 hours, sand using 400-grit abrasive to remove
gloss before recoating.
Health and Safety:
See Safety Data Sheet and labels for additional safety information and handling instructions.
* The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and SDS’s of all components, since
the mixture will have the hazards of all its parts.
* Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
* Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide adequate ventilation for health and fire hazard control.
* Follow company, product SDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on SDS.
* Always observe all applicable precautions and follow good safety and hygiene practices.
* Safety Data Sheets are available on website.